Astro-pneumatic 888S Short Straight Line Sander Manuel d'utilisateur
Naviguer en ligne ou télécharger Manuel d'utilisateur pour Outils Astro-pneumatic 888S Short Straight Line Sander. Astro Pneumatic 888S Short Straight Line Sander User Manual Manuel d'utilisatio
- Page / 4
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Call 1.800.221.9705 for questions concerning performance of the product
or other inquiries.
Page 4
888S
372 Old US Highway 52 South
Mount Airy, NC 27030
Product: 888SManual
Dimension: 8.5"x 15"/page
Date: 2008/07/17
Color:
Black
outside
MINI STRAIGHT
LINE SANDER
Housing Assembly
Piston
Piston Ring
Plug
Gasket
Rear Cover
Bushing
O-Ring
O-Ring
Valve Stem
Spring
Pin
Inlet
Screw
Bearing
Gear Shaft
Gear
Roller
Valve
Gear
Adjusting Shaft
Screw
O-Ring
Wear Plate
Wear Plate
Screw
Carrier Plate
Strap
Screw
Pad
Washer
Nut
Handle
Trigger
Pin
Screw
Screw
Knob
Muffler
1
1
4
2
1
1
1
2
1
1
1
1
1
4
2
2
1
1
1
1
888S-01
888S-02
888S-03
888S-04
888S-05
888S-06
888S-07
888S-08
888S-09
888S-10
888S-11
888S-12
888S-13
888S-14
888S-15
888S-16
888S-17
888S-18
888S-19
888S-20
888S-21
888S-22
888S-23
888S-24
888S-25
888S-26
888S-27
888S-28
888S-29
888S-30
888S-31
888S-32
888S-33
888S-34
888S-35
888S-36
888S-37
888S-38
888S-39
1
1
1
2
2
8
1
2
8
1
2
2
1
1
1
2
4
1
1
www.astrotools.com
Unpacking
When unpacking, check the parts diagram and part number listing
on page 4 to make sure all parts are included. If any parts are
missing or damage, please call your distributor.
•Astro Pneumatic Tool Co. warrants our products to the original user against
defective material or workmanship for a period of 1 year (except where noted on our
price schedule) from the date of 1st use. Astro reserves the right to determine
whether the product failed because of defective material, workmanship or other
causes and to charge back for missing parts. Astro Pneumatic Tool Co., at its
discretion, will repair products covered under this warranty free of charge. The
distributor should direct the original user to return the product (with the exceptions
listed below) with the distributor’s name, address, adequate proof of date of
purchase or a copy of warranty card, and a short note explaining the problem.
Failures caused by accident, alteration, or misuse are not covered by this
warranty.
•Astro Pneumatic Tool Co. or its authorized service representatives must perform all
warranty repairs. Any repair to the product by unauthorized service representatives
voids this warranty. The rights under this warranty are limited to the original user and
may not be transferred to subsequent owners.
•This warranty is in lieu of all other warranties, expressed or implied, including
warranties of merchantability and fitness for a particular purpose. Some states do
not allow the exclusion of limitations of incidental or consequential damages so the
above limitations may not apply to you. All claims must be sent to:
Astro Pneumatic Tool Company
372 Old US Highway 52 South
Mt. Airy, NC 27030
1 YEAR LIMITED WARRANTY
888S
PLEASE DO NOT RETURN ANY PRODUCT WITHOUT CALLING
1-800-221-9705 FOR INSTRUCTIONS
MINI STRAIGHT
LINE SANDER
• Used on plastic fillers at any stage of hardening
• Feathers with ease and smoothness
• Single Piston
• Single handle design for smaller and
harder to reach spaces
• Fast and efficient performance
• 3,000 strokes per minute
• 4 CFM
• Vibration less than 2.5 m/s2
SPECIFICATIONS:
• Sanding Paper Size: 2-3/4" x 11"
(7 x 28 cm)(PSA or Velcro)
• Tool Weight: 4.25 lbs (1.9kgs)
• Sound pressure: 89 dBA
• Sound Power: 98 dBA
MINI STRAIGHT LINE SANDER
MADE IN TAIWAN
Page 2 Page 3
inside
1.) LUBRICATION:
Before connection of the hose, apply 4 to 5 drips of a good
quality air tool oil at the air inlet. After 3 to 4 hours of opera-
tion, oiling may be necessary again.
3.) STORAGE:
Avoid storing the tool in a location subject to high humidity. If
the tool is left unused, the residual moisture inside the tool
can cause rust. Before storing and after operation, oil the tool
at the air inlet with a good quality air tool oil and run it for a
short period.
4.) DISPOSAL:
Follow national legislation of waste disposal.
5.) ORDERING SERVICE PART
For further operational and handling information or for
replacement of parts and components, contact the sales
agent from where you purchased the tool, or the service
division of our company. *When ordering parts and compo-
nents, give each part number, name, and quantities.
2.) TIGHTNESS OF PARTS:
Regularly check whether all connection parts are
fastened securely. Follow this precedure daily
before beginning work.
MINI STRAIGHT LINE SANDER
888S
MINI STRAIGHT LINE SANDER
888S
MINI STRAIGHT LINE SANDER
• Used on plastic fillers at any stage of hardening
• Feathers with ease and smoothness
• Single Piston
• Single handle design for smaller and
harder to reach spaces
• Fast and efficient performance
• 3,000 strokes per minute
• 4 CFM
• Vibration less than 2.5 m/s2
SPECIFICATIONS:
• Sanding Paper Size: 2-3/4" x 11"
(7 x 28 cm)(PSA or Velcro)
• Tool Weight: 4.25 lbs (1.9kgs)
• Sound pressure: 89 dBA
• Sound Power: 98 dBA
The oil and water extractor should not be mounted on or near the air
compressor.
The temperature of air is greatly increased during compression. As the air
cools down to room temperature, in the air line, on its way to the Air Power
Tool, the moisture contained in it condenses. Thus, for maximum
effectiveness, the oil and water extractor should be mounted at some point
in the air supply system where the temperature of the compressed air in the
line is likely to be lowest. Air lines must be properly drained daily. Each low
point in an air line acts as a water trap. Such points should be fitted with an
easily accessible drain. See diagram below. Pitch all air lines back towards
the compressor so that condensed moisture will flow back into the air
receiver where it can be drained off. Drain daily.
SUGGESTED AIR LINE CONNECTION
Pitch pipe back toward air receiver
Compressor unit
Drain
Daily
25 FEET OR MORE
Oil and Water Extractor should be at least 25 ft. from the compressor. Further if possible.
Drain
Daily
Drain
Daily
Oil and Water
Extractor
Install drain at
each low point
PIPE SIZE, I.D. (Inches)
Air Flow
CFM
Length of Pipe (feet)
10
20
30
40
50
70
50
1/2"
3/4"
3/4"
1"
1"
1"
100
3/4"
3/4"
3/4"
1"
1"
1"
150
3/4"
3/4"
1"
1"
1"
1-1/4"
200
3/4"
1"
1"
1"
1-1/4"
Résumé du contenu
Page 1 - LINE SANDER
Call 1.800.221.9705 for questions concerning performance of the productor other inquiries.Page 4888S372 Old US Highway 52 South Mount Airy, NC 27030Pr
Page 2
Call 1.800.221.9705 for questions concerning performance of the productor other inquiries.Page 4888S372 Old US Highway 52 South Mount Airy, NC 27030Pr
Page 3
Call 1.800.221.9705 for questions concerning performance of the productor other inquiries.Page 4888S372 Old US Highway 52 South Mount Airy, NC 27030Pr
Page 4
Call 1.800.221.9705 for questions concerning performance of the productor other inquiries.Page 4888S372 Old US Highway 52 South Mount Airy, NC 27030Pr
Produits connexes et manuels pour Outils Astro-pneumatic 888S Short Straight Line Sander
Outils Astro-pneumatic 7835 5pc. Impact Socket Set - Chrome Protective Pl Manuel d'utilisateur
(1 pages)
(1 pages)
Outils Astro-pneumatic 7859 Universal Cooling System Pressure Tester Manuel d'utilisateur
(10 pages)
(10 pages)
Outils Astro-pneumatic 1442 13 Nut/Thread Setting Hand Riveter Kit with 3 Manuel d'utilisateur
(3 pages)
(3 pages)
Outils Astro-pneumatic 78205 UNIVERSAL STEERING KNUCKLE SPREADER TOOL Manuel d'utilisateur
(4 pages)
(4 pages)
© 2020, manymanuals.fr. Tous droits réservés | 3.183 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels